von Topi » So 23. Jul 2023, 16:54
Hi,
ich habe Schwierigkeiten ein Koordinatensystem an einem bestimmten Punkt einzuzeichnen. Ich bekomme es nicht hin und wäre über Hilfe sehr dankbar. Das ist mein bisheriger code:
\begin{figure}
\centering
\usetikzlibrary {3d}
\usetikzlibrary{svg.path}
\begin{tikzpicture}[scale = 7]
\begin{scope}[
plane origin={(0,0,0)},
plane x={(0,0,1)},
plane y={(1,0,0.5)},
canvas is plane,]
\draw[very thick] (1,0,0) arc (0:180:1cm);
\draw[dashed] (1,0,0) -- (-1,0,0);
\draw[thick, -stealth, blue!60!green] (0,0,0) -- (60:1cm) node[midway, anchor =south west]{$\boldsymbol{r}(s)$};
\draw[thick, -stealth, blue!60!green] (0.3,0,0) arc (0:60:0.3cm) node[below, midway]{$\varphi = \frac{s}{R}$};
\draw[thick, -stealth, blue!60!green] (1.04,0,0) arc (0:59.5:1.04cm) node[midway, below]{$s$};
\end{scope}
\begin{scope}[plane origin={(0,0,0)},
plane x={(0,0,1)},
plane y={(0,1,0)},
canvas is plane,]
\draw[thick, red, stealth-] (1.05,0,0) arc (0: 200: 0.1cm) node[above, midway]{$\theta_\mathrm{entry}$};
\draw[thick, red, -stealth] (-0.95,0,0) arc (0:200:0.1cm) node[above, midway]{$\theta_\mathrm{exit}$};
\end{scope}
\end{tikzpicture}
\caption{Caption}
\label{fig:enter-label}
\end{figure}
Das Koordinatensystem sollte entsprechend dem Bild aussehen.
Wäre toll wenn jemand einen Rat parat hätte
- Dateianhänge
-
- 1-s2.0-S0020746223000835-gr3.jpg (17.52 KiB) 4484 mal betrachtet
Hi,
ich habe Schwierigkeiten ein Koordinatensystem an einem bestimmten Punkt einzuzeichnen. Ich bekomme es nicht hin und wäre über Hilfe sehr dankbar. Das ist mein bisheriger code:
[code]\begin{figure}
\centering
\usetikzlibrary {3d}
\usetikzlibrary{svg.path}
\begin{tikzpicture}[scale = 7]
\begin{scope}[
plane origin={(0,0,0)},
plane x={(0,0,1)},
plane y={(1,0,0.5)},
canvas is plane,]
\draw[very thick] (1,0,0) arc (0:180:1cm);
\draw[dashed] (1,0,0) -- (-1,0,0);
\draw[thick, -stealth, blue!60!green] (0,0,0) -- (60:1cm) node[midway, anchor =south west]{$\boldsymbol{r}(s)$};
\draw[thick, -stealth, blue!60!green] (0.3,0,0) arc (0:60:0.3cm) node[below, midway]{$\varphi = \frac{s}{R}$};
\draw[thick, -stealth, blue!60!green] (1.04,0,0) arc (0:59.5:1.04cm) node[midway, below]{$s$};
\end{scope}
\begin{scope}[plane origin={(0,0,0)},
plane x={(0,0,1)},
plane y={(0,1,0)},
canvas is plane,]
\draw[thick, red, stealth-] (1.05,0,0) arc (0: 200: 0.1cm) node[above, midway]{$\theta_\mathrm{entry}$};
\draw[thick, red, -stealth] (-0.95,0,0) arc (0:200:0.1cm) node[above, midway]{$\theta_\mathrm{exit}$};
\end{scope}
\end{tikzpicture}
\caption{Caption}
\label{fig:enter-label}
\end{figure}[/code]
Das Koordinatensystem sollte entsprechend dem Bild aussehen.
Wäre toll wenn jemand einen Rat parat hätte